How To Fix A Xbox One Controller Analog Stick

How to replace the springs in an Xbox One controller analog stick?

Here’s how to replace an Xbox One controller analog stick: Disassemble your controller using a pry tool and T-8 or T-9 safety Torx to take apart the case and a T-7 Torx to remove the circuit board. Use a desoldering tool to remove the old analog stick assembly from the circuit board. Insert the new analog stick assembly, and solder it in place.
To fix Xbox One controller drift, you need to take the controller apart and repair or replace one or more components related to the analog sticks. What Is Xbox One Controller Drift? The most common situation involves drift in the left analog stick, which usually manifests in your character constantly looking up in first-person games.
Rotate the thumbstick incrementally, carefully cleaning the entire thing. Check to make sure that you’ve fully cleaned the thumbstick, and test operation. If the thumbstick still sticks or drifts, disassemble your Xbox One controller using a pry tool and T-8 or T-9 safety Torx.
If the thumbstick still sticks or drifts, disassemble your Xbox One controller using a pry tool and T-8 or T-9 safety Torx. Check the thumbsticks to see if they’re positioned correctly, and try wiggling them to see if they’re loose.

How to fix Xbox One controller drift?

It’s called controller drift, or analog stick drift, because one or both thumbsticks will drift, or move, in an undesired direction even when you aren’t touching them. To fix Xbox One controller drift, you need to take the controller apart and repair or replace one or more components related to the analog sticks.
Left or Right analog stick drift on Xbox One and Series X/S can seem to be the most frustrating thing to fix if you are out of the warranty. Even though you can pry open the controller to do the fixes, there are ways you can fix this without even opening your controller.
The potentiometer, a part connected to the joystick that’s responsible for sending movement signals to your console, is an especially sensitive piece—a broken or defective one is likely to result in this issue. Before you start searching for how to take an Xbox One controller apart, try these simple steps to fix joystick drift.
Rotate the thumbstick incrementally, carefully cleaning the entire thing. Check to make sure that you’ve fully cleaned the thumbstick, and test operation. If the thumbstick still sticks or drifts, disassemble your Xbox One controller using a pry tool and T-8 or T-9 safety Torx.

How to fix a broken Xbox One controller?

You can usually make them work (almost) like new with just about an hour’s time and some tiny screwdrivers. The supplies you’ll need to get your controller in fighting condition again are a flat-head screwdriver, T8H screwdriver , T6 screwdriver and an Xbox One conductive button pad repair kit.
– Unplug the XBox’s power-brick from the wall for 5 minutes, to be sure there everything is 100% discharged. – Plug the controller into one of the XBox’s USB ports. (I also *unplugged* everything else from all the other USB ports, so the controller was literally the only thing plugged into a USB port on the XBox.
The hardest screw to find is in the center of the controller where the battery goes. The front casing will come off in your hand when the last screw is released. Now your controller will look like this. Remove the rubber joystick covers by popping them off like a Lego brick. Then, wiggle the metal joysticks underneath to loosen them.
Don’t trash them just yet! Jammed buttons and joysticks that, well, stick are common problems when it comes to Xbox One controllers. If you’re ready to throw your wireless controller at the wall and buy a new one, hold up. You can usually make them work (almost) like new with just about an hour’s time and some tiny screwdrivers.

How do I replace the analog stick on my controller?

Make sure the holes in the board are clear of any excess solder or other debris, and drop the new analog in. The stick should be rather secure in the board so you can go ahead an flip it over to solder it in place. Once you have soldered it in, place the thumbstick back on and reassemble the controller.
Pull off the old one, put on the new one. Reassemble the controller and you’re all set. Ok, now for those of you who need to replace the analog joystick. You’ll need to remove the solder from the pins, thus liberating the broken analog joystick from the board.
You may need to pry the joystick from the board by wedging a flat head screwdriver under it and working it up. Be careful to not break off the solder pads on the underside of the board that correspond with the analog. If these come off, you will not be able to solder the new one on. As a side note. Be careful with your soldering iron!
Keep in mind, this is mostly a temporary fix, and the problem may persist in a few months, as the controller undergoes fatigue after prolonged use.

How to replace an Xbox One controller analog stick?

How to replace Xbox One controller thumbsticks Remove the battery door. Remove the batteries from the controller. Use the plastic pry tool to detach the rear grips from the controller body. (Once you’ve separated them, pull firmly to… You now have five screws to remove as shown in the image with …
It’s easier than you might think. Xbox One controllers wear out a lot quicker than you’d like, especially if you’re a heavy gamer. But, before you go running to buy a new one, think about repairing the one you have. If it still fundamentally works as it should but something is broken or worn, you can save a bundle by doing a home repair job.
As long as they’re compatible with the Xbox One controller, the method remains the same. Because the thumbsticks are on the front and all the screws to hold the controller together are on the back, you’ll need to do a complete teardown by following these steps. Remove the battery door. Remove the batteries from the controller.
Use the plastic pry tool to detach the rear grips from the controller body. (Once you’ve separated them, pull firmly to remove them from the body.) You now have five screws to remove as shown in the image with the T8 screwdriver. (The fifth is located beneath the battery label so you’ll have to pierce it or remove it entirely.)

How do you fix Xbox One controller drift?

When Xbox One controller drift occurs, there are three main causes: Worn out thumbstick pad: Each thumbstick consists of a boxy sensor component with a moveable shaft on top and a rubber or plastic component that snaps onto the shaft. If the rubber or plastic piece becomes worn, replacing or repairing it will fix your drift issue.
Left or Right analog stick drift on Xbox One and Series X/S can seem to be the most frustrating thing to fix if you are out of the warranty. Even though you can pry open the controller to do the fixes, there are ways you can fix this without even opening your controller.
Rotate the thumbstick incrementally, carefully cleaning the entire thing. Check to make sure that you’ve fully cleaned the thumbstick, and test operation. If the thumbstick still sticks or drifts, disassemble your Xbox One controller using a pry tool and T-8 or T-9 safety Torx.
Reassemble the controller and test operation. If you still experience drift after attempting to fix your thumbstick pads or determine that they were neither dirty nor loose, then the next easiest fix is to replace your thumbstick springs. If only one thumbstick is giving you trouble, only replace the springs on that thumbstick.

How do I Fix my Xbox One controller that won’t turn on?

If your controller works when plugged in, consider purchasing a long USB to micro USB cable and using the controller in wired mode. If this fix doesn’t work, the controller may have an internal fault and require professional repairs. Contact Microsoft for customer support.
When all else fails, connect the Xbox One controller to the console directly using a USB cable. In some cases, a wireless controller that won’t turn on with batteries installed, or with a charge and play kit, will work when connected with a USB cable.
Even though it’s pretty sturdy, it can break down for a number of reasons. You can usually tell it’s not working when the Xbox button doesn’t light up. When a controller is functioning normally, pressing the Xbox button causes it to flash and then stay on.
If your controller works when plugged in, consider purchasing a long USB to micro USB cable and using the controller in wired mode. If this fix doesn’t work, the controller may have an internal fault and require professional repairs.

Leave a Comment

Your email address will not be published.