How To Take Apart Xbox 360 Console

What do you need to take apart an Xbox 360?

Very small flathead screwdriver or a flat point such as a kitchen knife or pushpin Step 1. Disconnect ALL wires from xbox, once everything is disconnected hold power button in for 2 seconds to clear any electric charge left in the console Step 2. Remove Hard Drive and any memory unit/cards you might have plugged into the console.
Just remember that if you screw up your XBox 360 more than it already is, you don’t really have a leg to stand on in regards to your warranty, so it is advised that you call and check out your warranty options. WARNING: THIS WILL VOID YOUR XBOX WARRANTY.
If you are hoping to open a Xbox 360 controller, you will need a Security Torx T8H. The best ones I’ve found are from Llamma’s Tool Section. Small Flathead Screwdrivers/Paper Clips – Used to hold open the friction locks of the 360 front cover.
On the right side of the 360 there is a notch at the end of the faceplate. Put your thumb on this notch and pull away from the console with a good deal of force.

How do I remove the 360 from the console?

Steps Assemble the equipment you’ll need. Disconnect your Xbox 360 from all input and output sources. Ground yourself before taking apart your Xbox 360. Pry off the faceplate. Release the end grilles. Remove the end grilles. Unclip the front of the case. Unclip the back of the case. Remove the bottom of the case.
Remove the bottom of the case. Flip the Xbox 360 so that its top is face-down, then pull the bottom of the case up and away from the Xbox 360. You should now be looking at the metal part of the Xbox 360’s case. Take out the screws holding the top of the case in place.
Gently ease your flathead screwdriver under the green ribbon on the left side of the console’s front face and pry. The eject button should pop right off. Lift the top of the case off of the Xbox 360. The case should pull right off, and you should now be looking at your Xbox 360’s internal components.
1 Poke a large, bent paperclip through each of the holes in the top row of ventilation spaces on the Xbox 360’s casing,… 2 Insert a flathead screwdriver into the space where the grille meets the console case, then work the screwdriver around… 3 If you have a hard drive on your Xbox 360, first remove it. More …

Is it possible to disassemble the Xbox 360?

Xbox Disassembly 1 Xbox Disassembly. Start with your Xbox unplugged and sitting on a flat, stable surface. 2 Flip the Xbox over and pry off the rubber feet with a metal spudger. 3 Peel back both the silver sticker and the white barcode sticker to reveal two additional screws. More items…
On the right side of the 360 there is a notch at the end of the faceplate. Put your thumb on this notch and pull away from the console with a good deal of force.
First remove the hard drive on the console, flip it over and with your thumb in the faceplate notch, remove the faceplate. On the right side of the 360 there is a notch at the end of the faceplate. Put your thumb on this notch and pull away from the console with a good deal of force. The plate should pop off of the casing.
They are located on the upper right corner, lower right, and lower left corners of disk drive. The screw on the lower left corner of the disk drive is not in the hole that it appears to be in, but rather just closer to the corner. Lift the hard drive storage unit out of the Xbox. It should come right out.

How do you remove the faceplate on a Xbox 360?

Detach the faceplate from the rest of the device. The faceplate is still attached to the console by a thin ribbon cable. Do not attempt to completely remove the faceplate yet. Using a spudger or fingernail, lift the clear blue tab away from the connector.
1 Orient the console right-side up, with the faceplate facing toward you. 2 Locate the two clips connecting the right and left case along the top edge of the console, behind the Wi-Fi card. 3 While pushing the left and right case away from each other with one hand, pry the clips away from the case with a metal spudger.
Insert a metal spudger between the top vent and the top bezel near the rear of the Xbox. Rotate the spudger away from the console, prying the edge of the fan vent up until the two plastic clips come free. Be sure to rotate the spudger far enough so that the plastic clips clear the silver rim of the top bezel.
Take care when removing the fan vent not to break any of the plastic clips. Orient the console so that the words “XBOX 360” on the sides are right-side up, and the faceplate is facing to the left. Insert a metal spudger between the top vent and the top bezel near the rear of the Xbox.

How do I take apart my Xbox 360?

First remove the hard drive on the console, flip it over and with your thumb in the faceplate notch, remove the faceplate. On the right side of the 360 there is a notch at the end of the faceplate. Put your thumb on this notch and pull away from the console with a good deal of force. The plate should pop off of the casing.
On the right side of the 360 there is a notch at the end of the faceplate. Put your thumb on this notch and pull away from the console with a good deal of force.
Insert a flat-head screwdriver into its lock point and pull off the shroud, it will take some wiggling to remove. Remove the fan power cable from the motherboard. Finally, lift up on the metal tap above the fans, and pull the fan casing towards the front of the console.
The plate should pop off of the casing. On each end of the console there are two gray heating grills which must be removed to take apart the console. For each grill there are six friction tabs that must be pressed inwards toward the console and lifted up.

How do I remove the case from my Xbox 360?

Here is the step by step process to take the cover off without damaging your console: The process begins with removing the hard drive from the console. Start by flipping the Xbox sideways and remove the clips to the plastic grates using a flat head screw driver. Once they have been flipped open, gently pull them out.
Steps Assemble the equipment you’ll need. Disconnect your Xbox 360 from all input and output sources. Ground yourself before taking apart your Xbox 360. Pry off the faceplate. Release the end grilles. Remove the end grilles. Unclip the front of the case. Unclip the back of the case. Remove the bottom of the case.
The process begins with removing the hard drive from the console. Start by flipping the Xbox sideways and remove the clips to the plastic grates using a flat head screw driver. Once they have been flipped open, gently pull them out.
Gently ease your flathead screwdriver under the green ribbon on the left side of the console’s front face and pry. The eject button should pop right off. Lift the top of the case off of the Xbox 360. The case should pull right off, and you should now be looking at your Xbox 360’s internal components.

How do I get the eject button off my Xbox 360?

If you need more info about your Xbox 360 console, visit the Xbox forums. This page describes how to manually eject the disc tray from your Xbox 360 console when the eject button doesn’t work. Disconnect the power cable and any other cables connected to the console. Uncoil a large paper clip.
Insert the flat end of a spudger between the eject button and the optical drive. Pry the eject button off its retaining posts and remove it from the 360. This can also be accomplished using an Xbox 360 opening tool. Almost done! To reassemble your device, follow these instructions in reverse order.
Use the tip of a spudger to release the clip securing the eject button to the metal casing. Insert the flat end of a spudger between the eject button and the optical drive. Pry the eject button off its retaining posts and remove it from the 360.
Be careful not to excessively bend the lower case near the power plug, as it can crack easily. Use the tip of a spudger to release the clip securing the eject button to the metal casing. Insert the flat end of a spudger between the eject button and the optical drive. Pry the eject button off its retaining posts and remove it from the 360.

Leave a Comment

Your email address will not be published.