How to take off Xbox One cover without damaging it?
When taking the case off of the Xbox One S, take care to not damage the clips. Flip the Xbox One S so that the bottom of the case is facing upward. Insert the plastic opening tool into the gap between the bottom of the case and the grated top side. Then find the clips in between that hold the case in place.
By sticking with the combo of a dust cloth, and compressed air you should be able to easily clean out your Xbox without accidentally causing any damage to it. While getting your console clean and shiny again only takes a few minutes, it’s also worthwhile to go ahead and clean off your controllers on a regular basis as well.
Flip the Xbox One S so that the bottom of the case is facing upward. Insert the plastic opening tool into the gap between the bottom of the case and the grated top side. Then find the clips in between that hold the case in place. Use the opening tool to pop the clips out. The best method is to pry the black case away from the bottom.
This article explains how to take apart an Xbox One controller if it needs repairs, keeping in mind potential snags and specialized tools you’ll need. Xbox One controllers are generally accepted as one of the best video game controllers around, but they still break down from time to time.
How do you remove the back of an Xbox 360?
On the right side of the 360 there is a notch at the end of the faceplate. Put your thumb on this notch and pull away from the console with a good deal of force.
Here is the step by step process to take the cover off without damaging your console: The process begins with removing the hard drive from the console. Start by flipping the Xbox sideways and remove the clips to the plastic grates using a flat head screw driver. Once they have been flipped open, gently pull them out.
First remove the hard drive on the console, flip it over and with your thumb in the faceplate notch, remove the faceplate. On the right side of the 360 there is a notch at the end of the faceplate. Put your thumb on this notch and pull away from the console with a good deal of force. The plate should pop off of the casing.
The first step is to remove the outer plastic shell that conceals the innards of the system. To do this, you must start by removing the face plate. Take a look at the front of the Xbox 360 and insert your thumb into the door that covers the two USB ports on the right of the unit.
How do you remove the faceplate on a Xbox 360?
Detach the faceplate from the rest of the device. The faceplate is still attached to the console by a thin ribbon cable. Do not attempt to completely remove the faceplate yet. Using a spudger or fingernail, lift the clear blue tab away from the connector.
1 Orient the console right-side up, with the faceplate facing toward you. 2 Locate the two clips connecting the right and left case along the top edge of the console, behind the Wi-Fi card. 3 While pushing the left and right case away from each other with one hand, pry the clips away from the case with a metal spudger.
Insert a metal spudger between the top vent and the top bezel near the rear of the Xbox. Rotate the spudger away from the console, prying the edge of the fan vent up until the two plastic clips come free. Be sure to rotate the spudger far enough so that the plastic clips clear the silver rim of the top bezel.
Take care when removing the fan vent not to break any of the plastic clips. Orient the console so that the words “XBOX 360” on the sides are right-side up, and the faceplate is facing to the left. Insert a metal spudger between the top vent and the top bezel near the rear of the Xbox.
What do you need to take apart an Xbox 360?
Very small flathead screwdriver or a flat point such as a kitchen knife or pushpin Step 1. Disconnect ALL wires from xbox, once everything is disconnected hold power button in for 2 seconds to clear any electric charge left in the console Step 2. Remove Hard Drive and any memory unit/cards you might have plugged into the console.
If you are hoping to open a Xbox 360 controller, you will need a Security Torx T8H. The best ones I’ve found are from Llamma’s Tool Section. Small Flathead Screwdrivers/Paper Clips – Used to hold open the friction locks of the 360 front cover.
Just remember that if you screw up your XBox 360 more than it already is, you don’t really have a leg to stand on in regards to your warranty, so it is advised that you call and check out your warranty options. WARNING: THIS WILL VOID YOUR XBOX WARRANTY.
On the right side of the 360 there is a notch at the end of the faceplate. Put your thumb on this notch and pull away from the console with a good deal of force.
How do I remove the 360 from the console?
Steps Assemble the equipment you’ll need. Disconnect your Xbox 360 from all input and output sources. Ground yourself before taking apart your Xbox 360. Pry off the faceplate. Release the end grilles. Remove the end grilles. Unclip the front of the case. Unclip the back of the case. Remove the bottom of the case.
Remove the bottom of the case. Flip the Xbox 360 so that its top is face-down, then pull the bottom of the case up and away from the Xbox 360. You should now be looking at the metal part of the Xbox 360’s case. Take out the screws holding the top of the case in place.
Reset your Xbox 360 to factory settings if you’re selling it or experiencing major issues. This will delete everything on the Xbox 360, but it will not remove parental restrictions. To remove parental restrictions, you’ll need to prove to Microsoft that you are authorized to remove them.
Gently ease your flathead screwdriver under the green ribbon on the left side of the console’s front face and pry. The eject button should pop right off. Lift the top of the case off of the Xbox 360. The case should pull right off, and you should now be looking at your Xbox 360’s internal components.
How to fix Xbox 360 that won’t turn on?
1 Unplug the power supply from the console and the wall outlet. 2 Take your console and power supply to another room. 3 Plug the power supply into a working wall outlet. … 4 Reconnect the power supply cable to your console. 5 Make sure that all of the power supply connections are firmly secured. 6 Press the power button on your console.
Check the lights on the front of the Xbox 360. The ring of lights around your Power button can indicate what kind of problem you are experiencing. This can help determine how to go about fixing it: Green lights – The system is operating normally.
Check the light on your power supply. Your Xbox 360’s power supply also has a light on the back. This light can help you determine if your power supply is failing: No light – The power supply is not receiving power from the wall. Green light – The power supply is working correctly and the Xbox is on.
Look for bent pins in the USB ports. A common cause of failure for Xbox 360 consoles is bent pins in the USB ports causing a short circuit: Examine the USB ports on the Xbox 360, both in the front and in the back. If any of the pins inside are touching each other or the casing of the port, they are likely causing a short circuit.
How do I take the case off my Xbox One s?
When taking the case off of the Xbox One S, take care to not damage the clips. Flip the Xbox One S so that the bottom of the case is facing upward. Insert the plastic opening tool into the gap between the bottom of the case and the grated top side. Then find the clips in between that hold the case in place.
Flip the Xbox One S so that the bottom of the case is facing upward. Insert the plastic opening tool into the gap between the bottom of the case and the grated top side. Then find the clips in between that hold the case in place. Use the opening tool to pop the clips out. The best method is to pry the black case away from the bottom.
Push the sides of the white shell outwards, detaching the rear panel. Lift the main body of the Xbox One S from the upper casing. Flip the console over, with the fan pointing upwards.
Use your T9 and T10 Torx screwdrivers for this. The metal case is the last piece of the Xbox One that you need to remove in order to open it. There are eight total screws to remove; you’ll see a light “C” with a number next to or below the screws. Two of the screws are at the bottom of the fan box.